The article following next involving How to Install a Bathtub is totally enjoyable. Give it a try and draw your own personal assumptions.
Setting up a bathtub isn't precisely brain surgery, however it does require strong plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old bath tub with a new one is additionally a moderately hard job. If the old bathtub is easily obtainable, the job can relocate immediately; if you have to open up a wall to eliminate the old tub and place the new bath tub, the job is much harder. In either case, the job is within a home handyman's abilities, although you will require a helper to vacate the old tub as well as embeded in the brand-new one. Make sure you have actually qualified on your own for the job and also are comfortable trying it. Rather than working with a professional to take control of a halfway-completed project, it is far better to think about utilizing one prior to you begin. Opportunities are you may require a professional plumber to make tube links.
This write-up will aid you install a brand-new bath tub in your restroom if you have actually already gotten a new tub and also don't require to change the plan of your previous water pipes.
Your tools and also material checklist ought to consist of the following:
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your installation, then the first thing you need to do is disconnect the supply of water. After doing so, switch on the faucets to drain any water staying in the system. The procedure of removing the existing taps can be rather bothersome as a result of the restricted gain access to that is often the case.
Utilize a container wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipelines to the faucets. Have a towel ready for the remaining water that will originate from the pipelines. As soon as the supply pipes have been eliminated, utilize the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to stop the solitary faucets from transforming during this procedure. As soon as the taps have been removed, the holes in the bath/basin will have to be cleaned up of any type of old securing substance.
Prior to going on to fit the brand-new taps, compare the pipe connections on the old taps to the new taps. If the old taps are longer than the new taps, after that a shank adapter is needed for the brand-new taps to fit.
Fitting New Taps
If the tails of the new taps are plastic, then you will need a plastic port to avoid damage to the thread. One end of the port fits on the plastic tail of the tap and the other end offers a connection to the existent supply pipes.
If you need to fit a monobloc, then you will call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next, place the tap in the installing hole in the bath/basin guaranteeing that the washers are in area in between the faucet as well as the sink. Protect the tap in place with the manufacturer given backnut. As soon as the faucet is safely in place, the supply pipes can be attached to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with normal faucet adapters. The former kind needs to be linked to the faucet finishes first, tightening only by hand. The supply pipelines can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Mounting the Tub
Using both wooden boards under its feet, position the tub in the required placement. The wooden boards are helpful in uniformly spreading the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto 4 small factors.
The following goal is to guarantee that the tub is leveled all round. This can be achieved by checking the level and readjusting the feet on the bathtub till the spirit level reads degree.
To install faucets, fit all-time low of the furthest adaptable tap adapter to the suitable supply pipe by making a compression join; after that do the exact same for the various other tap.
Switch on the water supply and inspect all joints and also new pipework for leakages and tighten them if needed. Fill the bathtub and likewise inspect the overflow electrical outlet and the normal outlet for leaks.
Lastly, take care of the bathroom paneling as defined in the supplier's instruction manual. Tiling and sealing around the tub must wait up until the bath tub has actually been made use of at least when as this will certainly resolve it into its final position.
Getting ready for the Installment
To start with, the sustaining frame supplied with the bathroom ought to be fitted (if needed) according to the producer's instructions. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is important to make sure that if the faucet features a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets system to avoid stress on the bathtub.
Fit the flexible tap connectors to the bottom of the two taps making use of 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet with the hole in the bath. Utilize the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make certain you utilize every one of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath should currently prepare to be fitted in its last setting.
Tiling Around the Bathtub
In the area where the bath satisfies the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is necessary as the installation can move sufficient to split a rigid seal, creating the water to pass through the wall between the bathroom and the tiling, leading to issues with dampness and also possible leaks to the ceiling listed below.
You can choose from a selection of coloured sealants to assimilate your fixtures and also installations. They are sold in tubes and also cartridges, and can securing spaces up to a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always fill up the bathtub with water prior to securing, to enable the activity experienced when the tub remains in use. The sealant can crack relatively early if you do not take into account this activity prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are also quickly available on the marketplace. It is recommended to fit the floor tiles utilizing waterproof or waterproof sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm very taken with How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I'm hoping you appreciated the entire blog posting. For those who appreciated our article please be sure to pass it around. We cherish reading our article about Installing A Bathtub.
Find Out More